filename: TFS70BE.doc version 1.2 26.11.2012 vectron international filter specification tfs 70be 1/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: * input: 1.6 || -7.7 pf output: 1.75 || -7.5 pf characteristics remark: the reference level for the relative attenuation a rel of the tfs 70be is the minimum of the pass band at tenuation a min . the minimum of the pass band attenuation a min is defined as the insertion loss a e . the centre frequency f c is the arithmetic mean value of the upper and lower frequencies at the 3 db filter attenuation level relative to the insertion loss a e . the nominal frequency f n is fixed at 70.0 mhz without any tolerance. the gi ven values for both the relative attenuation a rel and the group delay ripple have to be achieved at the frequencies given below even if the centre freq uency f c is shifted due to the temperature coefficient of frequency tc f in the operating temperature range and due to a pr oduction tolerance for the centre frequency f c . d a t a typ. value tolerance / limit insertion loss a e 13.3 db max. 15.0 db (reference level) nominal frequency f n - 70.0 mhz centre frequency at ambient temperature f c 70.0 mhz - pass band pb - f n 0.5 mhz pass band variation 0.4 db max. 0.8 db amplitude ripple in any 112.5 khz segment in pb 0.15 db max. 0.5 db relative attenuation a rel f n ? f n 0.5 mhz 0.4 db max. 0.8 db f n 1.1 mhz ? f n 1.5 mhz 42 db min. 37 db f n 1.5 mhz ? f n 3.0 mhz 42 db min. 40 db 0.3 mhz ? f n - 3.0 mhz 53 db min. 50 db f n + 3.0 mhz ? f n + 1.0 ghz 52 db min. 50 db group delay at f n 2.35 s max. 4 s group delay ripple within pb (in any 112.5 khz segment in pb) 70 ns max. 120 ns phase linearity within pb (in any 112.5 khz segment in pb) p-p 2.0 deg max. 5 deg input power level - max. 23 ** dbm operating temperature range otr - - 40 c ... + 70 c storage temperature range - - 40 c ... +100 c frequency inversion temperature 25 c - temperature coefficient of frequency tc f *** - 0.036 ppm/k 2 - *) the terminating impedances depend on parasitics and q-values of matching elements and the board use d, and are to be understood as reference values only. should there be additional questions do not h esitate to ask for an application note or contact o ur design team. **) this power level is only allowed for short term operation (10% of the life time), the max. input p ower for continuous operation is max.15dbm only ***) ? f(hz) = tc f (ppm/k2) x (t-t 0 )2 x f to (mhz) generated: checked / approved:
filename: TFS70BE.doc version 1.2 26.11.2012 vectron international filter specification tfs 70be 2/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. filter characteristic construction and pin connection (all dimensions in mm) date code 6 5 10 19 -0,10 +0,20 6,50 - 0,10 +0,20 1 2,0 max. 1,91 7,62 2,31 1,02 1 50 ohm test circuit 60 62 64 66 68 70 72 74 76 78 80 -80 -72 -64 -56 -48 -40 -32 -24 -16 -8 0 frequency in mhz magnitude in db 69 69.2 69.4 69.6 69.8 70 70.2 70.4 70.6 70.8 71 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 frequency in mhz magnitude in db 69 69.2 69.4 69.6 69.8 70 70.2 70.4 70.6 70.8 71 2.12 2.27 2.42 2.57 2.72 2.87 3.02 3.17 3.32 3.47 3.62 frequency in mhz delay in s tfs 70b e c21 date code: year + week c 2012 d 2013 e 2014 ... 1 input 2 ground 3 ground 4 ground 5 output 6 output 7 ground 8 ground 9 ground 10 input l1 l2 c1 saw l4 l5 l6 1 5 2, 3, 4, 7, 8, 9 6 10
filename: TFS70BE.doc version 1.2 26.11.2012 vectron international filter specification tfs 70be 3/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or g respec tively, 1 octave per min, 10 cycles per plane, 3 pl anes; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 30 min. each / 1 0 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; 5. esd ansi/esd s20.20-1999 , class 1a for hbm this filter is rohs compliant (2002/95/eg, 2005/618 /eg) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 2000 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm so w do po e ct p2 p1 d1 bo ao pull off direc tion typ e pin marker date cod e t ko n w 2 w 1 a c the minimum bending radius is 45 mm. tape (all dimensions in mm) w :32,00 0,3 po :4,00 0,1 do :1,50 +0,1/-0 e :1,75 0,1 f :14,20 0,1 p2 :2,00 0,1 p1 :12,00 0,1 d1(min) :2,00 ao :7,10 0,1 bo :19,60 0,1 so :28,40 0,1 ct :25,5 0,1 reel (all dimensions in mm) a : 330 w1 :32,4 +2/-0 w2(max) :38,4 n(min) : 100 c :13,0 +0,5/-0,2
filename: TFS70BE.doc version 1.2 26.11.2012 vectron international filter specification tfs 70be 4/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: TFS70BE.doc version 1.2 26.11.2012 vectron international filter specification tfs 70be 5/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 - generation of development specification strehl 07.11.2007 1.1 - correct group delay ripple within pb strehl 20.05.2008 - correct pass band ripple - correct phase linearity within pb - add terminating impedances - add typical values - add filter characteristics - add matching circuit - generation of filter specification 1.2 - remove previous screening requirements, (now with std screening only). tcuk 26.11.2012
|
